ENGINEERING RESOURCES

Understand the material.
Design a better part.

A practical reference for engineers, chemists, and product teams working with polyurethane and molded components. Explore the properties that matter, then bring your requirements to TPC.

Browse topicsAll topicsMechanicsEnvironmentDesign
Thank you! Your submission has been received!
Oops! Something went wrong while submitting the form.

22 engineering topics

Mechanics

Modulus of elasticity

Modulus describes resistance to deformation. Use it to understand how a component will deflect under load, beyond its hardness number.Explore topic

Elastomers do not behave like a simple metal spring across their full stretch range. Stiffness changes with strain, temperature and loading speed. A stress-strain curve or modulus at a stated strain is more useful than an unspecified modulus value. For design analysis, request data that represents the material and the conditions the finished part will experience.

What to specify

  • Loading mode and expected strain
  • Temperature and rate of loading
  • Required deflection or force response
Discuss your application
Mechanics

Hardness

Hardness measures resistance to indentation. A Shore value helps define a material, but it does not fully describe stiffness or durability.Explore topic

Always state the hardness scale with the number, such as Shore A or Shore D. The scales use different indenters and loads, so their values are not interchangeable. Measurement conditions also matter. Compare like-for-like test results, then check the properties that control your application: deflection, wear, tear resistance, grip or recovery.

What to specify

  • Shore scale and target hardness
  • Acceptable hardness variation
  • Part thickness and measurement location
Discuss your application
Mechanics

Tear strength

Tear strength describes resistance to a cut growing through the material. It matters around sharp edges, notches and repeatedly flexed features.Explore topic

A tear result depends on the specimen shape, test speed and how the tear starts. Values from different test methods cannot be treated as directly equivalent. Identify where a part could be nicked, stretched or caught in service, and evaluate the material and geometry together. A laboratory value supports comparison; it does not predict service life by itself.

What to specify

  • Likely cut or notch locations
  • Direction and speed of loading
  • Applicable tear test and acceptance target

Technical references

ASTM D624 — Tear strength
Discuss your application
Mechanics

Compression set

Compression set is the deformation left after a compressed part has been released and allowed to recover under stated test conditions.Explore topic

A part may feel firm while loaded yet fail to recover enough afterward. Compression-set testing helps compare materials for pads, seals and mounts that must retain their shape. State the compression, exposure temperature, time and recovery period when comparing results. Constant-force and constant-deflection tests describe different conditions; choose the approach that reflects the application.

What to specify

  • Compression level and time under load
  • Operating temperature
  • Recovery time and allowable permanent change
Discuss your application
Environment

Chemical resistance

Chemical compatibility depends on the exact formulation, fluid, concentration, temperature and exposure time. Start with the complete operating environment.Explore topic

Oil, cleaning agents, water and solvents can affect polyurethane in different ways. Swelling, softening or strength loss may occur even when a part still looks intact. Use compatibility information to shortlist materials, then evaluate the selected formulation with the actual fluids and service conditions. Include cleaning and maintenance exposure, not only normal operation.

What to specify

  • Chemical names, mixtures and concentrations
  • Temperature and exposure duration
  • Immersion, splash or intermittent cleaning
Discuss your application
Environment

Temperature range

Temperature changes an elastomer's stiffness and response. Define both normal operation and short excursions before choosing a material or process.Explore topic

A single temperature limit does not describe how a part performs under load. Cold conditions may reduce flexibility, while heat can change stiffness and accelerate degradation. Identify startup, continuous operation and cleaning conditions separately. Review the chosen formulation at the relevant temperatures, together with its loading, exposure time and surrounding environment.

What to specify

  • Minimum, normal and peak temperatures
  • Time at each temperature
  • Required flexibility and loading at temperature
Discuss your application
Environment

Flame resistance

Flammability requirements must name a test and classification. A general material description cannot establish the fire performance of a finished component.Explore topic

Tests such as UL 94 evaluate defined specimens under controlled conditions. Results depend on the applicable method and specimen thickness; classifications from different methods are not automatically equivalent. Share the required rating early so the exact material and part requirements can be reviewed. A material rating alone does not certify the complete product or assembly.

What to specify

  • Required test and classification
  • Minimum wall thickness
  • Material identification and supporting documentation
Discuss your application
Mechanics

Resilience / rebound

Rebound describes how much an elastomer springs back after an impact. It helps distinguish energy-return behavior from a more damped response.Explore topic

High rebound and low rebound serve different purposes. The right choice depends on whether your part should return motion or reduce bounce. Compare results made with the same instrument, specimen conditions and temperature. Rebound is a useful material-screening property, but the response of a finished wheel, bumper or pad must be evaluated in its actual geometry.

What to specify

  • Desired bounce or energy-return behavior
  • Impact speed and operating temperature
  • Rebound method used for comparison
Discuss your application
Mechanics

Bulk modulus

Bulk modulus describes resistance to a change in volume. It becomes especially important when an elastomer is confined on multiple sides.Explore topic

A soft elastomer can change shape readily while resisting a change in volume. Restricting its ability to bulge can therefore produce a much stiffer response than an unconfined test suggests. Review the surrounding cavity and available clearance, rather than using hardness alone to predict compression. Use appropriate material data when modeling confined parts.

What to specify

  • Confinement and available bulge space
  • Pressure and allowable movement
  • Material model and compressibility data
Discuss your application
Environment

Electrical resistivity

Electrical resistivity describes resistance to current flow through a material. Define the electrical function before selecting a polyurethane formulation.Explore topic

Insulating, static-dissipative and conductive applications require different targets. Specify whether the requirement concerns the surface, the material volume or the complete assembly, and identify the relevant test conditions. Do not infer electrical performance from color or hardness. The exact formulation and finished component need verification against the application's electrical requirements.

What to specify

  • Electrical function and resistivity target
  • Surface or volume measurement method
  • Conditioning, environment and assembly requirements
Discuss your application
Environment

Food contact polyurethane

Food-contact suitability applies to a specific material and intended use. Define the contact conditions and required documentation before material selection.Explore topic

The phrase “food grade” is not enough to specify a part. Identify the food type, contact time, temperature and cleaning conditions. Material composition and the applicable authorization or declaration must match the intended use. Ask for documentation for the selected formulation, including relevant additives and colorants, rather than assuming all polyurethane is suitable for food contact.

What to specify

  • Food type, contact time and temperature
  • Cleaning and repeated-use conditions
  • Required market and material documentation
Discuss your application
Mechanics

Coefficient of friction

Friction is a property of two contacting surfaces in use. Grip and sliding behavior depend on more than the polyurethane alone.Explore topic

A roller on paper and a guide sliding on steel present different requirements. Surface finish, mating material and wet or dry conditions affect the result. Distinguish the force needed to start movement from the force needed to maintain it. Compare candidate materials using a representative contact setup and the intended operating conditions.

What to specify

  • Mating material and surface finish
  • Dry, wet or lubricated contact
  • Required grip or sliding behavior
Discuss your application
Mechanics

Damping

Damping dissipates mechanical energy during deformation. It can help control vibration or bounce when matched to the full component and system.Explore topic

Material damping changes with the conditions of motion, including frequency. A formulation that works well at one operating point may respond differently at another. Describe the vibration or impact you want to control and the movement the part can accommodate. Evaluate the assembled component, because material behavior alone does not define system performance.

What to specify

  • Vibration frequency or impact conditions
  • Supported load and available movement
  • Temperature and desired response
Discuss your application
Design

Color

Color can support identification, appearance and product branding. Define the visual target together with the material's exposure and performance requirements.Explore topic

A color reference is a starting point, not a complete appearance specification. Review samples in the intended material, thickness and finish. Polyurethane chemistry influences light stability, so discuss sunlight exposure and acceptable color change early. For controlled applications, the selected colorant also belongs in the material review rather than being treated as a purely cosmetic choice.

What to specify

  • Color reference and approved physical sample
  • Surface finish and opacity
  • UV exposure and acceptable appearance change
Discuss your application
Mechanics

Abrasion resistance

Abrasion resistance describes how a material withstands wear from rubbing or abrasive contact. The wear mechanism matters as much as hardness.Explore topic

Sliding, grit and repeated contact can create different wear patterns. Use a test that represents the application and compare results obtained under the same conditions. In a volume-loss test, lower loss indicates better performance within that test. Laboratory rankings are useful for screening, but they do not establish a finished part's service life.

What to specify

  • Abrasive material and contact surface
  • Load, speed and wet or dry conditions
  • Wear limit and comparison test
Discuss your application
Mechanics

Tensile strength

Tensile strength measures resistance to pulling failure. Read it alongside elongation and the stress-strain response at the part's working deformation.Explore topic

Ultimate tensile strength describes a failure point, not an allowable working load for every component. Test speed, temperature, conditioning and specimen shape affect the result. Compare data under matching conditions and identify the strains expected during use. For parts that stretch or flex repeatedly, fatigue and tear behavior may also govern the design.

What to specify

  • Working strain and tensile load
  • Temperature and loading rate
  • Test method and acceptance criteria
Discuss your application
Design

Molding methods

Match the molding process to the material, part geometry and production needs. TPC offers open casting, injection molding and precision compression molding.Explore topic

Open casting forms parts from liquid urethane that cures in a mold. Injection molding fills a closed tool with a suitable molding material, including thermoplastics such as TPU. Compression molding shapes material under pressure in a matched tool. Share your drawing, performance needs and expected quantities so the material and process can be reviewed together.

What to specify

  • Drawing, dimensions and critical features
  • Material and performance requirements
  • Prototype, batch and annual quantities
Discuss your application
Mechanics

Load application

Describe how a part is loaded, not only how much it carries. Compression, tension, shear, impact and rolling contact produce different demands.Explore topic

A load value needs context: where it acts, how long it remains and how much movement is acceptable. Static loads and repeated cycles should be identified separately. Include contact area, support geometry and any preload in the drawing or brief. Compression-deflection data can help compare candidate materials for parts that must carry load while yielding predictably.

What to specify

  • Load direction, magnitude and contact area
  • Static, cyclic, rolling or impact loading
  • Allowable deflection and supporting geometry
Discuss your application
Mechanics

Fatigue

Fatigue concerns damage under repeated loading. Evaluate the full duty cycle, including deformation, heat buildup, rest periods and the surrounding environment.Explore topic

A part may withstand a single load yet degrade when that load repeats. Laboratory fatigue tests help compare formulations under defined conditions, but they do not automatically predict field life. Describe the expected cycles and failure criteria, then validate the chosen design with a representative test. Include speed and cooling conditions when repeated compression can generate heat.

What to specify

  • Cycle frequency and target operating life
  • Minimum and maximum deformation
  • Temperature, rest periods and failure criteria
Discuss your application
Design

Dimensional tolerances

Specify tolerances around how the part fits and functions. Identify critical dimensions early, together with a consistent method for measuring them.Explore topic

Soft parts can deform under the pressure of a measuring instrument. Agree on the measurement method and conditions as well as the dimensions themselves. Mark mating features, fit requirements and the dimensions that control performance on your drawing. TPC can review those requirements with the proposed material and process before a production tolerance is agreed.

What to specify

  • Critical dimensions, datums and fit
  • Material condition during inspection
  • Measurement method and acceptance limits
Discuss your application
Mechanics

Hysteresis

Hysteresis is the energy lost as an elastomer is loaded and unloaded. It connects material behavior with damping and heat generation.Explore topic

Loading and unloading do not follow exactly the same force-displacement path. The enclosed loop represents energy dissipated during a cycle. That loss may be useful for damping, but repeated deformation can also create unwanted heat. Consider the intended motion, cycle rate and operating temperature when balancing energy absorption against efficient recovery.

What to specify

  • Deformation amplitude and cycle rate
  • Energy absorption or recovery target
  • Permissible temperature rise
Discuss your application
Design

Bonding

A bonded component combines an elastomer with a substrate or insert. Treat the interface as a designed feature with its own requirements.Explore topic

Bond performance depends on the substrate, its surface condition, the bonding system and the molding process. Specify the metal or other insert material, coatings and service environment early. Plan verification that reflects the forces acting at the interface. A representative adhesion test and an agreed failure criterion help evaluate the complete bonded construction.

What to specify

  • Substrate material, coating and condition
  • Peel, shear or tensile loads at the bond
  • Exposure conditions and bond acceptance test
Discuss your application

No matching topics.

Try a broader term or reset the library.

Show all topics

This guide supports material and part discussions. Final properties depend on the selected formulation, geometry, and operating conditions. Confirm the applicable data, test method, and acceptance criteria for your part.

Colorful molded urethane parts, bushings, and blocks
POLYURETHANE / MANY SHAPES. APPLICATION-SPECIFIC REQUIREMENTS.

YOUR NEXT STEP

Put the guidance
to work.

Bring your operating conditions, a drawing, and the properties that matter. Let’s review your part together.

Book a meeting Prepare your project brief